Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 47

Page: 47 / 162

Intel

Server System SR2612UR Service Guide

Installing the Disk Drives

Caution: Before installing new disk drives, acclimate them to room temperature. Store drives at

room temperature for two hours prior to use.

Note: To install a disk drive or plastic blank into a carrier, refer to

“Drive Installation in the

Drive Carrier” on page 75

in this manual.

1. Select an open drive slot.

2. Hold the disk drive so the LEDs are on the left and the lever is fully open.

3. Slide the disk drive into the drive slot until the lever starts to close.

Figure 24. Sliding the Disk Drive into the Drive Slot

4. Push the lever until it meets the latch on the left side of the drive slot and clicks into

place.

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands