Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 41

Page: 41 / 162

Intel

Server System SR2612UR Service Guide

Hot-Swap SAS/SATA Backplane

The backplane serves as an interface between the midplane board and the system drives.

The hot-swap backplane provides support for both SAS and SATA hard drives. There are
no hard drive cables that connect to the backplane. All hard drive control signals are
routed from the midplane board, which plugs directly into the backplane.

Figure 18. 3.5-inch Hot-Swap SAS/SATA Backplane Components (Front View)

Figure 19. 3.5-inch Hot-Swap SAS/SATA Backplane Components (Rear View)

SAS/SATA Hard Disk Drive Connectors

Backplane Power Connector

Midplane Board Connector

Server Board/Midplane GPIO Connector

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands