Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 132

Page: 132 / 162

118

Intel

Server System SR2612UR Service Guide

Redundant Hot-swappable Components

•

Two power supply modules

•

Two independent AC power inlets with domestic NEMA power cords

•

Up to 12 drives

Maximum Cable Lengths (Customer Supplied)

•

3 Gbps SAS: Up to 6m

•

1 Gb Ethernet: up to 10m

Raid Features

•

RAID 0,1,10,5,50,6,60 (PCI RAID adapter dependant)

•

OS software RAID capable

•

Auto-negotiate speeds

•

In-band and out-of-band management

•

SAS/SMP/SSP protocol support

•

Redundant cable support

2U Rackmount Enclosure

•

Dimensions: 3.5 inches H x 17.6 inches W x 31 inches D (8.9 cm H x 44.7 cm W x
78.7 cm D)

•

Weight with drives: 70 lbs (35 kg) max

•

Standard Rackmount Rail Kit Adjustable Depth: 28.0 inches to 34.0 inches (71.1 cm to
86.4 cm)

Disk Drives

•

12 independent 300MB/s point-to-point connections to each SAS or SATA disk drive

•

Common universal dual-purpose drive carrier/ blank for all 3.5-inch NDS standard
products

•

Form factor:

•

External: 3.5-inch SAS and SATA HDDs

•

Internal: 2.5-inch SATA HDDs/SSDs (single or dual)

•

Rotational speed: 7200 RPM, 10K RPM, and 15K RPM

•

Interface: 3 Gb SAS; 3 Gb/1.5 Gb SATA

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands