manualshive.com logo in svg

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

The Intel SR2612UR Server System is a powerful and reliable solution for your server needs. This product includes a comprehensive Service Manual, which can be downloaded for free from our website. With detailed instructions and troubleshooting tips, this manual is essential for optimizing the performance and maintenance of your server system.

Share
Download
background image

viii

Intel

®

 Server System SR2612UR Service Guide

Tools and Supplies Needed  ........................................................................................ 29
System References ..................................................................................................... 29
Preparing for Installation  ............................................................................................. 29

Installing Your Intel

® 

Server System SR2612UR into a Rack (Optional)  ............................ 30

Installing the Disk Drives  ..................................................................................................... 33
Removing a Disk Drive Carrier Assembly (or Drive Blank)  ................................................. 35

Important Safety Precautions ...................................................................................... 35
Removing a Disk Drive ................................................................................................ 35
Installing the Operating System  .................................................................................. 37

Connecting Your Intel

® 

Server System SR2612UR to a Host Server  ................................. 38

Connecting to the 1GE iSCSI LAN Data Ports ............................................................ 38
Connecting Additional Enclosures .............................................................................. 38
Powering On  ............................................................................................................... 38

Installing a 2.5-inch Internal Drive  ....................................................................................... 39
DVD Installation ................................................................................................................... 41
Replacing a Fan  .................................................................................................................. 43
Installing a Fan  .................................................................................................................... 44
Midplane Board Replacement  ............................................................................................. 45

Memory Installation  ..................................................................................................... 46

PCI Card and Battery Installation  ........................................................................................ 48
Power Supply Replacement  ................................................................................................ 51
Replacing the Backplane Board  .......................................................................................... 51

Removing the Backplane Board .................................................................................. 52

Installing and Removing the RAID Battery Backup Unit ...................................................... 54

Installing the RAID Battery Backup Unit (BBU) ........................................................... 54

Installing and Removing the Server Board .......................................................................... 57

Removing the Server Board ........................................................................................ 57
Installing the Server Board .......................................................................................... 60

Replacing the Backup Battery  ............................................................................................. 62
Removing and Installing the Power Distribution Module  ..................................................... 63

Removing the Power Distribution Module  ................................................................... 63
Installing Power Distribution Module  ........................................................................... 65

Chapter 4: Server Utilities  ........................................................................................69

Using the BIOS Setup Utility  ............................................................................................... 69

Entering BIOS Setup ................................................................................................... 69
If You Cannot Access Setup  ....................................................................................... 69
Setup Menus  ............................................................................................................... 69

Upgrading the BIOS  ............................................................................................................ 71

Preparing for the Upgrade ........................................................................................... 71
Upgrading the BIOS  .................................................................................................... 72

Clearing the Password  ........................................................................................................ 72
Restoring the BIOS Defaults  ............................................................................................... 74

Appendix A: Drive Installation in the Drive Carrier  ...............................................75

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Reviews:

No comments

Related manuals for SR2612UR - Server System - 0 MB RAM

NEC NECCare Platinum Express5800/A1160 Brochure & Specs preview
NECCare Platinum Express5800/A1160
Brand: NEC Pages: 4
NEC NECCare Gold Express5800/320Fd Maintenance And Service Manual preview
NECCare Gold Express5800/320Fd
Brand: NEC Pages: 11
NEC NEC Express5800/R120d-2E Configuration Manual preview
NEC Express5800/R120d-2E
Brand: NEC Pages: 39
NEC UNIVERGE NEAX 2000 IPS Manual preview
UNIVERGE NEAX 2000 IPS
Brand: NEC Pages: 244
NEC UNIVERGE NEAX 2000 IPS General Description Manual preview
UNIVERGE NEAX 2000 IPS
Brand: NEC Pages: 191
NEC UNIVERGE NEAX 2000 IPS Configuration Manual preview
UNIVERGE NEAX 2000 IPS
Brand: NEC Pages: 96
Xblue Networks X-25 Installation Manual preview
X-25
Brand: Xblue Networks Pages: 148
IBM 8649 - Eserver xSeries 225 Maintenance And Troubleshooting Manual preview
8649 - Eserver xSeries 225
Brand: IBM Pages: 194
Radware APSolute Vision Installation And Maintenance Manual preview
APSolute Vision
Brand: Radware Pages: 81
Artesyn AXP640 Installation And Use Manual preview
AXP640
Brand: Artesyn Pages: 190
Supero SuperServer 6026TT-HIBQF User Manual preview
SuperServer 6026TT-HIBQF
Brand: Supero Pages: 112
W&T Com-Server++ Manual preview
Com-Server++
Brand: W&T Pages: 228
Edimax EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0 User Manual preview
EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0
Brand: Edimax Pages: 118
Xerox DocuColor 45087638 User Addendum preview
DocuColor 45087638
Brand: Xerox Pages: 28
Blackberry Enterprise Server 33 Reference Manual preview
Enterprise Server 33
Brand: Blackberry Pages: 207
Olive O3HD Quick Start Manual preview
O3HD
Brand: Olive Pages: 103
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual preview
DCX 8510-8
Brand: Brocade Communications Systems Pages: 176
RIOT CloudLink Installation Manual preview
CloudLink
Brand: RIOT Pages: 18

Brands by name

Popular brands

Load more brands