background image

Intel

®

 Server System SR2612UR Service Guide

1

1

Server System Contents and 
References

Server System Contents

The Intel

® 

Server System SR2612UR ships with the Intel

®

 Server Board S5520UR. For 

information about the server board, see the 

Intel

®

 Server Board SR2612UR Technical 

Product Specification

.

The contents of the Intel

® 

Server System SR2612UR are listed in the following section.

Intel

®

 Server System SR2612UR Contents

Your Intel

®

 Server System SR2612UR ships with the following items:

Storage Application Array

Adjustable rackmount kit

Two plastic rack ear covers

Product CD

Attention Doc

Disk Drive Specifications

The Intel

®

 Server System SR2612UR supports up to 12 SAS and/or SATA disk drives.

Disk drives and two optional 2.5-inch fixed 3 Gbps SATA hard drives must meet these 
specifications and must be qualified for Intel

®

 Server System SR2612UR:

7200, 10,000, or 15,000 rpm

Hot-swap/hot-plug support

SATA or SAS device plug connector

3 Gb/sec (or 300 MB/sec) data rate for SAS and SATA, 1.5 Gb/sec data rate for 
SATA

3.5-inch form factor, 1-inch high

Cable Specifications

To connect your Intel

®

 Server System SR2612UR to a host using the dual integrated 1GE 

iSCSI ports, use high-quality Cat5e ethernet cables that meet these length requirements:

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Reviews: