User’s Manual
Using the system
27
•
Codes
- deactivated (disabled) codes cannot access the system.
•
Keys
- deactivated (disabled) keys cannot access the system.
•
Keypads
- deactivated (disabled) keypads cannot provide access to the
system, therefore, cannot generate commands or shortcuts. However, the
LEDs and display will be refreshed.
•
Readers
- deactivated (disabled) readers cannot provide access to the
system, therefore, cannot accept keys or generate commands. However, the
LEDs will indicate the current status of the system.
•
Timers
- activated timers (On) manage their associated elements (partitions,
codes, keys) in accordance with their settings. Deactivated timers cannot
time-manage their associated elements (partitions, codes, keys), therefore,
they will function in accordance with Timer Off status.
Note
All the timers will be activated automatically when you exit the programming session. You
must deactivate timers which are not used for system control purposes.
•
Dialer
- a deactivated (disabled) dialer cannot send voice or digital calls.
However, if duly programmed, it will be able to manage incoming calls.
•
Answerphone function
- if activated (enabled), the control panel will answer
incoming calls with the pre-recorded voice message (“Answerphone
message”).
•
Teleservice
- if activated (enabled), the installer will be able to access the
system via modem. The Teleservice call allows the installer to work on the
control panel parameters. Teleservice operations involve a request from you
and the installers acceptance, therefore, this option needs to be enabled only
when required.
Note
If the “Answerphone” and “Teleservice” functions are both enabled, the control panel will
give incoming-call priority to the Teleservice call. After picking up the call, the control
panel will allow the installer-company modem 30 seconds to establish communication. If
the modem fails to communicate within this period, the control panel will play the pre-
recorded “Answerphone” voice message.
•
Internet access -
If this option is enabled, and the system is equipped with a
SmartLAN/G board, the control panel will allow user-authorized access to the
system via LAN/Internet. If this option is disabled, the control panel will allow
user-authorized access to the system via Teleservice (if authorized).
•
Enable install.
If enabled, the Installer PIN will be accepted by the system
and the installer will have access to the Installer menu. If disabled, entry of
the installer PIN will generate an “Invalid Code” event and the installer will be
denied access to the respective menu.
Via Keypad
Method 1
Activate the shortcuts associated with keys ,
..., (shown on the display)
with or without code entry.
•
The shortcut assigned to the “Activations menu” (shortcut n.15:
), allows
you to view the respective section in the User Menu.
1. Use keys
and
followed by
to select the category of elements
you wish to activate/deactivate (zones, codes, etc.).
2. Use keys
and
followed by
, to select the single element you wish
to activate/deactivate.
3. Use
to activate the selected element or
to deactivate it.
•
Other shortcuts which provide direct access to sub-sections of the
“Activations” section are:
•• Shortcut n.19 (
) accesses “Activations/Zones”
•• Shortcut n.22 (
) accesses “Activations/Answerphone”
•• Shortcut n.23 (
) accesses “Activations/Teleservice”
•• Shortcut n.24 (
) accesses “Activations/Codes”
•• Shortcut n.25 (
) accesses “Activations/Keys”
•• Shortcut n.26 (
) accesses “Activations/Timers”
•• Shortcut n.27 (
) accesses “Activations/Auto-arm”
18:23 30/10/2011
DDDDDDD
User Code
Arm/Disarm op.
Voice functions
Activations
ACTIVATIONS
Zones
Codes
Keys
Type in code
******
Method 2
Method 2
Method 2
ZONE ACTIVATIONS
Panel T01
Panel T02
Panel T03
Method 1
Summary of Contents for SmartLiving 10100L
Page 45: ...User s Manual 45 Notes...
Page 46: ...46 User s Manual...
Page 47: ...User s Manual 47...
