IDT CPS-1848 User Manual Download Page 440 | Manualshive

Page: 440 / 450

background image

10. Registers > Lane Control Registers

CPS-1848 User Manual

440

June 2, 2014

Formal Status

This document is confidential and is subject to an NDA.

Integrated Device Technology

10.20.15 Broadcast Lane Error Rate Enable Register

A read of this register returns the last value written. Each port’s value may differ from this broadcast register. The per-port
version of this register is

Lane {0..47} Error Rate Enable Register

Register Name: BCAST_LANE_ERR_RATE_EN
Reset Value: 0x0000_0000

Register Offset: 0xFFFF10

Bits

0

1

2

3

4

5

6

7

00:07

Reserved

08:15

Reserved

16:23

Reserved

UNUSED

BAD_SPEE

D_EN

LANE_INV

ER_DET_E

N

24:31

IDLE2_FRA

ME_EN

Reserved

TX_RX_MIS

MATCH_EN

DESCRAM

_SYNC_EN

BAD_CHA

R_EN

LANE_RDY

_EN

LANE_SYN

C_EN

Bits

Name

Description

a

Type

Reset

Value

0:18

Reserved

Reserved

RO

0

19:21

UNUSED

Reserved

RW

0

22

BAD_SPEED_EN 0 = Disable

1 = Enable capturing that a link speed was requested that is not
supported because of the PLL configuration.

RW

0

23

LANE_INVER_DE

T_EN

0 = Disable
1 = Enable capturing that a lane polarity inversion was detected
and compensated for; only reported when correction is applied.

RW

0

24

IDLE2_FRAME_E

N

0 = Disable
1 = Enable capturing that an error was detected within the
received IDLE2 frame.

RW

0

25:26

Reserved

Reserved

RW

0

27

TX_RX_MISMATC

H_EN

0 = Disable
1 = Enable capturing that the link partner receiver and local
transmitter mismatched, long/short.

RW

0

28

DESCRAM_SYNC

_EN

0 = Disable
1 = Enable capturing of loss of receiver descrambler
synchronization while receiving scrambled control symbol and
packet data.

RW

0

«
...
438
439
440
441
442
...
»

Summary of Contents for CPS-1848



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CPS-1848

Brand: United Electric Controls Pages: 6

TECMA Silence Marine

Brand: Thetford Marine Pages: 9

Pow-R-Line SPX0361126

Brand: Eaton Pages: 584

MicroHub GUH274W3

Brand: IOGear Pages: 1

Brand: Ribimex Pages: 15

Brand: Delta Electronics Pages: 31

EXT-UHDA-HBTL-RX

Brand: Gefen Pages: 33

Brand: Cabletron Systems Pages: 83

Brand: Comm-Tec Pages: 48

Brand: Lightwave Pages: 53

Brand: Cypress Pages: 4

Brand: Unipoe Pages: 9

Brand: Cabletron Systems Pages: 116

ISCOM2600G (A) Series

Brand: Raisecom Pages: 96

Brand: WilTec Pages: 7

Brand: Comnet Pages: 105

Brand: Hamlet Pages: 2

R-INS-TAPT-WH02

Brand: Quirky Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands