Huawei G5500 User Manual Download Page 25

Page: 25 / 215

Figure 2-13

Ports on the rear panel of a server

1 PGND port

2 GE electrical port

3 10GE optical port 1 (LOM)

4 10GE optical port 2 (LOM)

5 Serial port

6 PSU socket

7 PSU handle

NOTE

Lower the handle of a PSU after it is installed.

If the G560 is installed, the 10GE optical ports are reserved. If the G530 V2 nodes are installed, they
serve as LOM ports.

2.6 Hard Disk Slot Numbers

Figure 2-14

shows hard disk slot numbers of a full-width compute node.

Figure 2-14

Hard disk slot numbers of a full-width compute node

Figure 2-15

shows hard disk slot numbers of a half-width compute node.

FusionServer G5500 Server
User Guide

2 Components

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

Summary of Contents for G5500
























































































































































































































Search results

Summary of Contents for G5500

Reviews:

Related manuals for G5500

Brands by name

Popular brands

Huawei G5500, User Manual

Search results

Summary of Contents for G5500

Reviews:

Related manuals for G5500

Brands by name

Popular brands