manualshive.com logo in svg

Huawei G5500, User Manual

Share
Download
Huawei G5500 User Manual Download Page 90

Parameter

Description

Value

ipaddr6

Specifies the IPv6 address of
the network port to be
configured.

The value is an IPv6 address in the
format of

xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxx
x

. When multiple continuous 

xxxx

 are 0,

the value is in the format of 

xxxx::xxxx

.

For example,

2001:0000:000:0000:0000:0000:0000:
0001

 can be written as 

2001::0001

.

An IPv6 address can contain only one
xxxx::xxxx.

prefixlen

Specifies the subnet prefix
length of the network port to
be configured.

0 to 128.

gateway6

Specifies the IPv6 gateway
address of the network port
to be configured.

The value is an IPv6 address in the
format of

xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxx
x

. When multiple continuous 

xxxx

 are 0,

the value is in the format of 

xxxx::xxxx

.

For example,

2001:0000:000:0000:0000:0000:0000:
0001

 can be written as 

2001::0001

.

An IPv6 address can contain only one
xxxx::xxxx.

 

Step 2

Configure other basic management module data.
For details about how to configure other basic data for the management module, see the

FusionServer G5500 Server 1.0.0 HMM Command Reference

.

----End

5.4 Configuring the G560

This topic describes how to configure the installed G560 to support upper-layer services.

Configuration Process

Figure 5-8

 shows the initial configuration process for the G560.

FusionServer G5500 Server
User Guide

5 Configuring the G5500

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

82

Summary of Contents for G5500
























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands