manualshive.com logo in svg

Huawei G5500, User Manual

Share
Download
Huawei G5500 User Manual Download Page 153

 

Step 4

Lower the ejector lever until it is latched. See (2) in Figure 2.

Step 5

Check whether the hard disk is installed successfully by observing the hard disk indicator
status. For details, see 

2.3 Front Panel Indicators and Buttons

.

----End

6.4.2 CPU

Installing a CPU

Step 1

Power off G530 V2. For details, see 

3.1 Powering Off the Compute Node

.

Step 2

Remove the G530 V2. For details, see 

3.5 Removing a G530 V2

.

Step 3

Place the G530 V2 onto the ESD floor.

Step 4

Remove the cover. For details, see 

Removing the Cover of a G530 V2

.

Step 5

Determine the location for installing the CPU.

Figure 6-27

 shows the numbering and locations of CPUs.

Figure 6-27

 Numbering and locations of CPUs

Step 6

Take a spare CPU out of its ESD bag.

NOTE

CPUs on the same server must have the same BOM number.

Step 7

Install a CPU carrier.
1.

Take the new CPU carrier out of its ESD bag.

FusionServer G5500 Server
User Guide

6 Optional Part Installation

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

145

Summary of Contents for G5500
























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands