Huawei G5500 User Manual Download Page 47

Page: 47 / 215

Figure 3-6

Opening the handles on both sides of the GP608

Pull the GP608 out of the chassis. See (2) in

Figure 3-6

Place the removed GP608 in an ESD bag.

NOTICE

An ESD bag can hold only one GP608.

----End

3.5 Removing a G530 V2

Step 1

Power off the G530 V2 to be removed. For details, see

3.1 Powering Off the Compute

Node

Step 2

Determine the position of the node. See

Figure 3-7

. The G530 V2 nodes are installed in the

two lower slots of the chassis, corresponding to G530 V2-1 and G530 V2-2. The GP316s are
installed in the two upper slots of the chassis, corresponding to GP316-1 and GP316-2.

Figure 3-7

Node slots

FusionServer G5500 Server
User Guide

3 Basic Operations

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

Summary of Contents for G5500
























































































































































































































Search results

Summary of Contents for G5500

Reviews:

Related manuals for G5500

Brands by name

Popular brands

Huawei G5500, User Manual

Search results

Summary of Contents for G5500

Reviews:

Related manuals for G5500

Brands by name

Popular brands