HPE OfficeConnect 1920S 24G series Management And Configuration Manual Download Page 115

Page: 115 / 209

PoE Port Schedule

115

Status

Indicates whether the interface is currently capable of routing IP packets (Up) or cannot route

packets (Down). For the status to be Up, the routing mode and administrative mode for the

interface must be enabled. Additionally, the interface must have an IP address and be

physically up (active link).

Routing Mode

The administrative mode of IP routing on the interface.

Admin Mode

The administrative mode of the interface. If an interface is administratively disabled, it cannot

forward traffic.

State

The state of the interface, which is either Active or Inactive. An interface is considered active

if the link is up, and the interface is in a forwarding state.

Link Speed Data Rate

The physical link data rate of the interface.

IP Address Configuration

Method

The method to use for configuring an IP address on the interface, which can be one of the

following:



None – No address is to be configured.



Manual – The address is to be statically configured. When this option is selected you can

specify the IP address and subnet mask in the available fields.



DHCP – The interface will attempt to acquire an IP address from a network DHCP

server.

DHCP Client Identifier

The DHCP Client Identifier (Option 61) is used by DHCP clients to specify their unique

identifier. DHCP servers use this value to index their database of address bindings. This value

is expected to be unique for all clients in an administrative domain. The Client Identifier string

will be displayed beside the check box once DHCP is enabled on the port on which the Client

Identifier option is selected. This web page will need to be refreshed once this change is

made.

IP Address

The IP address of the interface. This field can be configured only when the selected IP

Address Configuration Method is Manual. If the method is DHCP, the interface attempts to

lease an IP address from a DHCP server on the network, and the IP address appears in this

field (read-only) after it is acquired. If this field is blank, the IP Address Configuration Method

might be None, or the method might be DHCP and the interface is unable to lease an address.

Subnet Mask

The IP subnet mask for the interface (also known as the network mask or netmask). This field

can be configured only when the selected IP Address Configuration Method is Manual.

MAC Address

The burned-in physical address of the interface. The format is six two-digit hexadecimal

numbers separated by colons, for example 00:06:29:32:81:40.

IP MTU

The largest IP packet size the interface can transmit, in bytes. The IP Maximum Transmission

Unit (MTU) is the maximum frame size minus the length of the Layer 2 header.

Bandwidth

The configured bandwidth on this interface. This setting communicates the speed of the

interface to higher-level protocols.

Encapsulation Type

The link layer encapsulation type for packets transmitted from the interface, which can be

either Ethernet or SNAP.

Forward Net Directed

Broadcasts

Determines how the interface handles network-directed broadcast packets. A network-

directed broadcast is a broadcast directed to a specific subnet. If this option is selected,

network directed broadcasts are forwarded. If this option is clear, network directed broadcasts

are dropped.

Proxy ARP

When this option is selected, proxy ARP is enabled, and the interface can respond to an ARP

request for a host other than itself. An interface can act as an ARP proxy if it is aware of the

destination and can route packets to the intended host, which is on a different subnet than the

host that sent the ARP request.

Local Proxy ARP

When this option is selected, local proxy ARP is enabled, and the interface can respond to an

ARP request for a host other than itself. Unlike proxy ARP, local proxy ARP allows the

interface to respond to ARP requests for a host that is on the same subnet as the host that

sent the ARP request. This feature is useful when a host is not permitted to reply to an ARP

request from another host in the same subnet, for example when using the protected ports

feature.

Field

Description

Summary of Contents for OfficeConnect 1920S 24G series


















































































































































































































Search results

Summary of Contents for OfficeConnect 1920S 24G series

Reviews:

Related manuals for OfficeConnect 1920S 24G series

Brands by name

Popular brands

HPE OfficeConnect 1920S 24G series, Management And Configuration Manual

Search results

Summary of Contents for OfficeConnect 1920S 24G series

Reviews:

Related manuals for OfficeConnect 1920S 24G series

Brands by name

Popular brands