manualshive.com logo in svg

HP AA979A - StorageWorks SAN Switch 2/8V, Administrator'S Manual, Page: 387 / 465

Share
Download
HP AA979A - StorageWorks SAN Switch 2/8V Administrator'S Manual Download Page 387

Fabric OS 5.3.0 administrator guide 393

21 Configuring and monitoring FCIP tunneling

The Fibre Channel over IP (FCIP) Tunneling Service is an optional feature that enables you to use Fibre 

Channel “tunnels” to connect SANs over IP-based networks. An FCIP tunnel transports data between a pair 

of Fibre Channel switches. You can have more than one TCP connection between the pair of Fibre Channel 

switches. However, from the Fibre Channel fabric point of view, the FCIP tunnel is just a connection 

between switches, and all the IP network and protocols remain invisible. 

Supported platforms for FCIP

Fabric OS supports FCIP ISLs between two HP StorageWorks switches (

400 MP Router

 or 4/256 SAN 

Director with an FR4-18i blade).
The GbE ports on the FC4-16IP do not support FCIP tunneling.

NOTE:

The FCIP Tunneling Service for the HP StorageWorks 400 MP Router or HP StorageWorks 

4/256 SAN Director with an FR4-18i blade is not compatible with the XPath FCIP service; nor is it 

compatible with any other vendor’s implementation

.

About FCIP tunneling

FCIP tunneling enables you to connect fabrics over an IP connection. Depending on the port type you 

select, the fabrics can merge or remain separate, while sharing devices. This enables you, for example, to 

connect one central office to different branch offices without having to merge the fabrics.
The port types for FCIP tunneling are either VE_Port or VEX_Port. An FCIP tunnel using VE_Ports will merge 

the two fabrics, and an FCIP tunnel using a VEX_Port will not merge the fabrics. A VEX_Port can only 

connect to a VE_Port.
Fibre Channel frame encapsulation on one port and the reconstruction of Fibre Channel frames on the 

other port is transparent to the initiator and target.
Fabric OS supports FCIP ISLs between two supported HP StorageWorks switches (400 MP Router or 4/256 

SAN Director with B-Series MP Router blade) or routers.
The tunnel on each GbE port are numbered 0 through 7, and each tunnel corresponds to a virtual GbE 

port. For example, tunnel 0 on GbE port 0 corresponds to logical FC port 16; tunnel 1 on GbE port 1 

corresponds to logical FC port 25. The GbE physical ports enable you to configure the following tunnels 

and corresponding virtual ports:

Table 97

Tunnels and virtual port numbering once configured

Physical ports

Tunnels

(portshow fciptunnel 

slot/ge)

Virtual ports

(switchshow

ge0

0 through 7

16 through 23

(area numbers might be different 

depending on the slot chosen for 

the B-Series MP Router blade)

ge1

0 through 7

24 through 31

(area numbers might be different 

depending on the slot chosen for 

the B-Series MP Router blade)

Summary of Contents for AA979A - StorageWorks SAN Switch 2/8V


















































































































































































































































































































































































































































































Reviews:

No comments