manualshive.com logo in svg

HP AA979A - StorageWorks SAN Switch 2/8V, Administrator'S Manual, Page: 29 / 465

Share
Download
HP AA979A - StorageWorks SAN Switch 2/8V Administrator'S Manual Download Page 29

Fabric OS 5.3.0 administrator guide

29

How to display network interface settings

If an IP address has not been assigned to the network interface (Ethernet), you must connect to the Fabric 

OS CLI using a console session on the serial port, see ”

How to connect via the serial port

” on page 26. 

Otherwise, connect using SSH.

1.

Connect to the switch and log in as admin.

2.

Enter the 

ipAddrShow

 command.

If the Ethernet IP address, subnet mask, and gateway address are displayed, then the network interface 

is configured. Verify that the information is correct. If DHCP is enabled, the network interface 

information was acquired from the DHCP server.

NOTE:

You can use either IPv4 or IPv6 with a Classless Inter-domain Routing (CIDR) block notation to set 

up your 

IP

 addresses.

Static Ethernet addressing summary

Use static Ethernet network interface addresses on SAN Director 2/128 and 4/256 SAN Director models, 

and in environments where DHCP service is not available. To use static addresses for the Ethernet interface, 

you must first disable DHCP. You may enter static Ethernet information and disable DHCP at the same time. 

Refer to 

Configuring DHCP

, page 30 for more information.

If you choose not use DHCP or to specify an IP address for your switch Ethernet interface, you can do so by 

entering none or 0.0.0.0 in the Ethernet IP address field.

CAUTION:

The use of IP address 0.0.0.0 is not supported in SANs running Fabric OS versions earlier 

than 5.2.x.

Fabric OS beginning with 2.6.0, 3.1.0, and 4.0.0 supports Classless Inter-Domain Routing (CIDR).

FD21:admin> 

ipaddrshow

SWITCH

Ethernet IP Address: 192.168.78.158

Ethernet Subnetmask: 255.255.255.0

Fibre Channel IP Address: 220.220.220.23

Fibre Channel Subnetmask: 255.255.255.0

Gateway Address: 192.168.78.1

DHCP: On

Summary of Contents for AA979A - StorageWorks SAN Switch 2/8V


















































































































































































































































































































































































































































































Reviews:

No comments