manualshive.com logo in svg

HP AA979A - StorageWorks SAN Switch 2/8V, Administrator'S Manual, Page: 356 / 465

Share
Download
HP AA979A - StorageWorks SAN Switch 2/8V Administrator'S Manual Download Page 356

364 Administering ISL Trunking

Setting port speeds

For long-distance ports, if a port is set to autonegotiate port speed, the maximum speed (which is 4 

Gbit/sec) is assumed for reserving buffers for the port–this wastes buffers if the port is actually running at 2 

Gbit/sec. For long-distance ports, it is best to set the port speed (this applies to SAN Switch 4/32, SAN 

Switch 4/32B and 4/256 SAN Director only). 
You can set the port speed for one port or for an entire switch. Trunked ports must be set to the 

same speed.

To set the speed for one port

1.

Connect to the switch and log in as 

admin

.

2.

Enter the 

portCfgSpeed

 command. The format is:

The following example sets the speed for port 3 on slot 2 to two Gbit/sec:

The following example sets the speed for port 3 on slot 2 to autonegotiate:

portcfgspeed

 [

slotnumber/

]

portnumber, speed_level

 

slotnumber

For bladed systems only, specify the slot number of the port to be configured, 

followed by a slash (/). This operand is only required for switches with slots, 

such as the SAN Director 2/128 and 4/256 SAN Director.

portnumber

Specifies the port number relative to its slot for bladed systems.

speedlevel

Specifies the speed of the link:

•

0—Autonegotiating mode. The port automatically configures for the 

highest speed.

•

1—one Gbit/sec mode. Fixes the port at a speed of one Gbit/sec. 

Changing the speed to one Gbit/sec causes the port to be excluded from 

the trunk group.

•

2—two Gbit/sec mode. Fixes the port at a speed of two Gbit/sec.

•

4—four Gbit/sec mode. Fixes the port at a speed of four Gbit/sec. (4/16 

SAN Switch and 4/8 SAN Switch, Brocade 4Gb SAN Switch for HP 

p-Class BladeSystem, Brocade 4Gb SAN Switch for HP c-Class 

BladeSystem, SAN Switch 4/32, SAN Switch 4/32B and 4/256 SAN 

Director only.)

switch:admin> 

portcfgspeed 2/3 2

 

done.

switch:admin>

switch:admin> 

portcfgspeed s/3 0

 

done.

switch:admin>

Summary of Contents for AA979A - StorageWorks SAN Switch 2/8V


















































































































































































































































































































































































































































































Reviews:

No comments