HP AA979A - StorageWorks SAN Switch 2/8V Administrator'S Manual Download Page 30

Page: 30 / 465

Performing basic configuration tasks

How to set static addresses for the Ethernet network interface

Connect to the switch and log in as admin.

Enter the following command to set the IPv4 address:

switch:admin>

ipaddrset

Ethernet IP Address [192.168.74.102]:

Ethernet Subnetmask [255.255.255.0]:

Fibre Channel IP Address [220.220.220.2]:

Fibre Channel Subnetmask [255.255.0.0]:

Gateway IP Address [192.168.74.1]:

DHCP [OFF]: off

To set an IPv6 address on a switch:

switch:admin> ipaddrset -ipv6 --add 1080::8:800:200C:417A/64

IP address is being changed...Done.

Example:

director:admin> ipaddrset -ipv6 -sw 0 --add 1080::8:800:200C:417B/64

IP address is being changed...Done.

Enter the network information in dotted decimal notation for Ethernet IPv4 address and semicolon separate

notation for IPv6. Enter the Ethernet Subnetmask and Gateway Address at the prompts. Press

Enter

to skip

Fibre Channel prompts. Type

Off

to disable DHCP.

NOTE:

You can use either IPv4 or IPv6 with a CIDR block notation to set up your IP addresses.

Configuring DHCP

By default, some HP switches have DHCP enabled. SAN Director 2/128 and 4/256 SAN Director models

do not support DHCP.
The Fabric OS DHCP client supports the following parameters:

•

External Ethernet port IP addresses and subnet masks

•

Default gateway IP address

The DHCP client uses a DHCP vendor class identifier that allows DHCP servers to determine that the

Discovers and Requests are coming from an HP switch. The vendor class identifier is the string “BROCADE”

followed by the SWBD model number of the platform. For example, the vendor class identifier for a request

from a SAN Switch 2/32 (SilkWorm 3900) is “BROCADESWBD12.”

NOTE:

The client conforms to the latest IETF Draft Standard RFCs for

IPv4, IPv6 and DHCP

Summary of Contents for AA979A - StorageWorks SAN Switch 2/8V


















































































































































































































































































































































































































































































Search results

Summary of Contents for AA979A - StorageWorks SAN Switch 2/8V

Reviews:

HP AA979A - StorageWorks SAN Switch 2/8V, Administrator'S Manual, Page: 30 / 465

Search results

Summary of Contents for AA979A - StorageWorks SAN Switch 2/8V

Reviews: