manualshive.com logo in svg

HP AA979A - StorageWorks SAN Switch 2/8V, Administrator'S Manual, Page: 203 / 465

Share
Download
HP AA979A - StorageWorks SAN Switch 2/8V Administrator'S Manual Download Page 203

Fabric OS 5.3.0 administrator guide 205

By index

With the introduction of 48-port blades, the Index was introduced. Unique area IDs are possible up to 255 

areas, but beyond that there needed to be some way to ensure uniqueness.
A number of fabric-wide databases supported by Fabric OS (including ZoneDB, Secure FOS DDC policies, 

the ACL DDC, and Admin Domain) allow a port to be designated by the use of a “D,P” (Domain, Port) 

notation. While the “P” component appears to be the port number, in up to 255 ports it was actually the 

area

 assigned to that port.

If the PID format is changed from Core to Extended-edge or vice-versa, the “P” value for ports 0-127 also 

changes. If two ports are changed using the portSwap command, their respective areas and “P” values are 

exchanged. 
For ports that are numbered above 255, the “P” value is actually a logical index. The existing 

index-to-area_ID mapping for the first 256 ports in a switch is kept, and add values equal to the physical 

port number for the new FC4-48 ports.
The first 256 ports continue to have an index value equal to the area_ID assigned to the port. If a switch is 

using Core PID format, and no port swapping has been done, the port Index value for all ports is the same 

as the physical port numbers. Changing the PID format will change the index values as well as the area_ID 

values of the first 128 ports, and using portswap on a pair of ports will exchange those ports’ area_ID and 

index values. Portswap is not supported for ports above 256.

Table 52

 and 

Table 53

 show the area ID and index mapping for core and extended-edge PID assignment. 

Note that up to 255 areas, the area_ID mapping to the index is one-to-one. Beyond this, the index is 

similar but not exact, and in some instances the area ID is shared among multiple ports.
These tables provide the area_ID/Index assignment for the maximum number of ports (used by the FC4-48 

blade). If your blade does not have the maximum number of ports, use the lower sections of the table to 

determine the area_ID and index.

Table 52

Default index/area_ID Core PID assignment with no port swap

Port on 

blade

Slot 

1Idx/Area

Slot 

2Idx/Area

Slot 

3Idx/Area

Slot 

4Idx/Area

Slot 

7Idx/Area

Slot 

8Idx/Area

Slot 

9Idx/Area

Slot 

10Idx/Area

47

271/135

287/151

303/167

319/183

335/199

351/215

367/231

383/247

46

270/134

286/150

302/166

318/182

334/198

350/214

366/230

382/246

45

269/133

285/149

301/165

317/181

333/197

349/213

365/229

381/245

44

268/132

284/148

300/164

316/180

332/196

348/212

364/228

380/244

43

267/131

283/147

299/163

315/179

331/195

347/211

363/227

379/243

42

266/130

282/146

298/162

314/178

330/194

346/210

362/226

378/242

41

265/129

281/145

297/161

313/177

329/193

345/209

361/225

377/241

40

264/128

280/144

296/160

312/176

328/192

344/208

360/224

376/240

39

263/143

279/159

295/175

311/191

327/207

343/223

359/239

375/255

38

262/142

278/158

294/174

310/190

326/206

342/222

358/238

374/254

37

261/141

277/157

293/173

309/189

325/205

341/221

357/237

373/253

36

260/140

276/156

292/172

308/188

324/204

340/220

356/236

372/252

35

259/139

275/155

291/171

307/187

323/203

339/219

355/235

371/251

34

258/138

274/154

290/170

306/186

322/202

338/218

354/234

370/250

33

257/137

273/153

289/169

305/185

321/201

337/217

353/233

369/249

32

256/136

272/152

288/168

304/184

320/200

336/216

352/232

368/248

31

143/143

159/159

175/175

191/191

207/207

223/223

239/239

255/255

Summary of Contents for AA979A - StorageWorks SAN Switch 2/8V


















































































































































































































































































































































































































































































Reviews:

No comments