¾
To adjust the brake force, pull out the bolt,
move the lever (1) to the desired position and
let it engage again.
Adjusting the brake valve unit
(workshop work)
Change the pressure settings only if the curb
weight of the machine has changed (e.g. by
attaching optional equipment).
WARNING
Danger of traffic accidents!
•
Changes to the pressure setting cause
changes in the response characteristics of
the brake system.
•
Reducing or increasing the pressure ratio may
cause a marked change of the braking power,
depending on the extent.
NOTE
For machine with road approval, changes to
the pressure settings may void the registration!
¾
Observe the data of the vehicle registration.
¾
Weigh the axle load of the empty machine in
transport position.
¾
Set the operating pressure to 6.5 bar on the
yellow coupler (pressure regulator and pres-
sure gauge are required).
¾
Connect a second pressure gauge to the test
port (7) of the brake valve unit.
8
9
¾
Set the regulator according to the pertaining
sticker (full and empty). Loosen the lever (8)
on the tooth shaft and adjust the tooth shaft (9).
Achslast
Axle load
Charge Essieu
kg
Ausgangsdruck
Output pressure
Pression de sortie
bar
A-1:
6.300
3.800
A-1:
6.700
4,3
4.500
4.100
4.100
3,2
A-1:
7.800
5.400
4.900
A-1:
8.400
5.400
A-1:
9.000
6.400
5.900
5.900
3,4
4,1
4,4
4,8
4,6
5,3
5,6
5,9
Achslast
Axle load
Charge Essieu
min. kg max.
Ausgangsdruck
Output pressure
Pression de sortie
bar
beladen
loaded
chargé
leer
emtpy
vidé
Eingangsdruck / Input pressure / Pression d´entrée
bar
6,5
WABCO 475 713 000 0
Ventil Nr. / Valve No. / Valve N°.
Maestro CV / CX M19
Einstellwerte der manuellen lastabhängigen Bremskraftregelung:
Settings of the manual load sensing device:
Valeurs de réglage de la correction de freinage manuelle asservie à la charge:
A-1:
7.200
4.900
4.500
3,7
4,9
60007016
Brake valve unit sticker
Releasing the brake
The brake of the parked machine can be re-
leased on the brake valve.
This is only possible if adequate air is present in
the air vessel to open the spring accumulator.
DANGER
Uncontrolled rolling of the machine can cause
severe injuries by crushing or rolling over.
¾
Park the machine only on level ground with
sufficient load bearing capacity.
¾
Before unhitching the machine: Secure the
machine with wheel chocks against rolling
away before releasing the brake.
¾
Press the button (5) to release the brake or
pull it out to apply the brake.
¾
Push the button (6) to release the parking
brake.
110
111
Summary of Contents for Maestro 12.45 CV
