Honeywell Dolphin 9900 Page 77 User Manual Download

Page: 77 / 170

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

4 - 9

AutoInstall.exm

The AutoInstall.exm file controls the behavior and appearance of the AutoInstall window and install
process.

Key Function

Default
Value

Available Values

Version

This is the current version of the AutoInstall.exm
file. This key is read-only and cannot be modified.

N/A

Debug

Enable and disables logging of debug information
to

\IPSM\AUTOINSTALL.LOG

0=Disabled
1=Enabled

Cancel

Enable and disables the Cancel button on the
AutoInstall window.

0=Disabled
1=Enabled

FullScreen

Determines if the AutoInstall window runs in full
screen mode (barring access to other windows).

0=Disabled
1=Enabled
2=Autoselects based

on the operating
platform.

HaltOnError

Sets the behavior of AutoInstall when an error is
encountered.

0=Log the error and

continue AutoInstall

1=Halt AutoInstall and

prompt the user to
continue or cancel

MaskPassword

If a password is entered in the Password key, this
key determines if that password is masked when
entered on the screen.

0=Disabled
1=Enabled

AutoInstall
window

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands