Honeywell Dolphin 9900 Page 89 User Manual Download

Page: 89 / 170

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

5 - 11

Centering Section

The Centering section determines the centering window for bar code scanning.

ScanWedge Entry

Description

Default
Value

Available Values

CenteringEnable=

Enable and disables the decode
centering window for the decoder.

0=Disabled; centering is

disabled for ScanWedge.

1=Enabled; bar codes are

decoded only if they are
within the centering window
specified by the rest of the
keys in this section.

CenteringTop=

Specifies the top coordinate of the
centering window.

210

Enter the coordinates in pixels.

CenteringBottom=

Specifies the bottom coordinate of
the centering window.

270

CenteringLeft=

Specifies the left coordinate of the
centering window.

346

CenteringRight=

Specifies the right coordinate of
the centering window.

406

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands