Honeywell Dolphin 9900 Page 83 User Manual Download | Manualshive

Page: 83 / 170

background image

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

5 - 5

SendMode

Specifies the method to use when
sending the decoded message to the
foreground application.

Note: This setting affects only the

decoded message; the prefix and
suffix are always sent using the
virtual key method to allow
navigational functionality.

0

0=Virtual key method: each

character is sent as a virtual
keystroke. This method
works well with almost any
Windows Mobile application.

1=Direct Text method: the

decoded message is sent as
text directly to the window
that has the keyboard focus
in the foreground application.
This method is faster than the
virtual key and supports
barcodes with ASCII
characters between 1 and
255 but works only if the
foreground application uses
standard Window’s Edit
controls for user input.

2=Virtual Key (safe) method:

each character is sent as a
virtual keystroke using
PostKeybdMessage().
This method only support bar
codes containing ASCII
characters and does not
support VKMapping. This
method only generates
WM_CHAR messages, it
does not generate
WM_KEYDOWN and
WM_KEYUP messages.

GoodScanWav

Specifies a .wav file played on the
completion of a successful decode/data
reception.

Empty

Empty=No .wav file is specified.

The default beep or sound is
played. Use the

Sound

(page

5-3) key to enable and
disable all audio notification.

X=The path to the specific .wav

file you want played for either
option. The .wav files should
be 8-bit, 11KHz, mono, and
PCM.

BadScanWav

Specifies a .wav file played for an
unsuccessful decode/data reception.

Empty

Settings Section

The Settings section determines how ScanWedge interprets data from the decoder, serial port, and IrDA
interface.

0 = Disable 1 = Enable

Settings Section
Key

Description

Default
Value

Available Values

«
...
81
82
83
84
85
...
»

Summary of Contents for Dolphin 9900











































































































































































Reviews:

No comments

Related manuals for Dolphin 9900

Brand: Peak Pages: 10

Brand: Tripp Lite Pages: 3

Brand: Fein Pages: 74

Brand: Greencut Pages: 52

Brand: UNIROSS Pages: 2

Brand: UNIROSS Pages: 2

Pro Plus Online M2M

Brand: Wallbe Pages: 12

Brand: Thunder Pages: 16

Brand: Linear Technology Pages: 6

Brand: Quicksilver Pages: 7

Brand: Jupio Pages: 2

Brand: Dräger Pages: 2

Brand: Redpro Pages: 1

Terra AC wallbox UL

Brand: ABB Pages: 37

Brand: ABB Pages: 154

Terra AC Series

Brand: ABB Pages: 58

Brand: NRS Pages: 7

Brand: Sony Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands