Honeywell Dolphin 9900 Page 86 User Manual Download | Manualshive

Page: 86 / 170

background image

5 - 8

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

Decode Section

The Decode section specifies decoder settings when using the decoder with ScanWedge.

ScanWedge Entry

Description

Default
Value

Available Values

Enable

Enables and disables the decoder for
ScanWedge.

1

0=Disabled; decoder is not

used.

1=Enabled; decoder sends bar

code data as keystrokes to
the active window.

Trigger

Sets the key used by ScanWedge to
initiate a scan/decode. The key is
registered as a system hotkey and
cannot be registered as a hot key by
any other applications.

42

42=OnScan or Scan key

ContScan

Enables and disables continuous
scan.

0

0=Disabled; trigger key must be

released between scans.

1=Enabled; data is

continuously decoded and
sent to the application while
the trigger key is depressed.

PowerSave

Enables and disables power saving
mode.

1

1=Enabled; the decoder

automatically initializes and
un-initializes as needed. A
slight delay occurs when the
trigger is activated.

0=Disabled; the decoder

initializes when the utility
starts and un-initializes
when the utility terminates.

ScanTimeout

Specifies the decode time out in 1/
1000th seconds. If a barcode is not
decoded within the specified timeout
an audio and visual notification
indicates that an error occurred.

5000

X=Time in 1/1000th of a

second.

ScanMode

Specifies the decode mode.

1

1=Full Omni/Normal
2=ALD (Aggressive Linear

Decode) mode

4=Quick Omni

LinearRange

Specifies the linear search range to
be used while in ALD mode.

3

X=Range from 1 to 6.

1 indicates a tight vertical
range near the aimer.
6 indicates a vertical range
of the entire height of the
imager.

«
...
84
85
86
87
88
...
»

Summary of Contents for Dolphin 9900











































































































































































Reviews:

No comments

Related manuals for Dolphin 9900

Brand: Ciar Pages: 37

Brand: CE-Link Pages: 5

Brand: Beta Pages: 60

Brand: Quikcell Pages: 14

Brand: everActive Pages: 36

TS-MPPT-60-600V-48-DB-TR

Brand: Morningstar Pages: 45

Karate Nighthawk AC/DC

Brand: YUKI MODEL Pages: 44

Brand: Quick Charge Pages: 4

Ultura - Ultura Digital Camcorder

Brand: Canon Pages: 103

Brand: Canon Pages: 6

Brand: Canon Pages: 2

BP 511 - 50D SLR Digital Camera

Brand: Canon Pages: 3

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Argus Pages: 32

M/Power MP-A Series

Brand: Humanscale Pages: 10

Brand: Sunoptic Surgical Pages: 36

Brand: Remote Audio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands