Honeywell Dolphin 9900 Page 56 User Manual Download

Page: 56 / 170

3 - 2

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

DeviceConfig.exm Sections and Keys

The sections and keys in the DeviceConfig.exm file are locked, which means that you can change values
but not names or descriptions.

Connections Section

The Connections section contains child sections that set communication parameters on the terminal.

Beam Section

The Beam section enables and disables the IrDA port.

Radio Manager Section

In the Radio Manager, typically, you would enable the radio in the WiFi section, enable DHCP in the
TCPIP section, then configure the radio settings in the Security\Supplicant\ProfileX or
Security\NonSupplicant section.

Section Name

Description

See Page

Connections

Configures communication parameters. There are child sections
that configure the IrDA port, the on-board radios, and the
ActiveSync connection.

3-2

System

Configures basic system settings.

3-9

Applications

Configures software applications.

3-10

WiFi Section

The keys in the WiFi section control the settings of the WLAN radio.

Key

Description

Default
Value

Available Values

Enable

Enables and disables the WLAN radio.

0=Disabled
1=Enabled; if enabled, the GSM radio

section is disabled automatically

PowerMode

Specifies the power save mode.

1=Disable; radio is powered

constantly (power save mode is
not used)

2=Always Enable; power save mode

is used

3=Auto Enable; EPSParm key

defines radio vs. battery
performance

EPSParm

When PowerMode is set to 3 (Auto
Enable), this parameter specifies radio
vs. battery performance.

N/A

X=A value between 1 and 10, where:
1=Best Radio Performance

(Minimum)

10=Best Battery Life (Maximum)

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands