Honeywell Dolphin 9900 User Manual Download Page 152

Page: 152 / 170

10 - 2

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

Modifying Menu Configuration Files

Menu configuration files can be modified in EZConfig Editor on the workstation or the terminal, If modified
on the workstation, the *Menu.exm file must be deployed to the terminal.

For details about modifying EXM files in EZConfig Editor:

• See

EZConfig Editor on page 2-2.

• See

EZConfig Editor on the Terminal on page 2-30.

Creating Menu Configuration Files

Save as the

Default EZMenu Configuration Files

(see page 10-1) to create new menu configuration files.

On the workstation, navigate to the following folder:

C:\Program Files\Honeywell\Power

Tools and Demos for WM 6.0\EZConfig EXM Files

Open a sample menu configuration file in EZConfig Editor.

Tap File > Save As and save the file with a new name ending in “Menu.exm.”

Modify the file; to see the available values, see

Menu Configuration File Sections

on page

10-3.

Save or transfer the file to the

\IPSM

folder on the terminal.

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Honeywell Dolphin 9900, User Manual, Page: 152 / 170

Search results

Summary of Contents for Dolphin 9900

Reviews: