Honeywell Dolphin 9900 Page 82 User Manual Download

Page: 82 / 170

5 - 4

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

SuffixID

Specifies the symbology identifier sent
after the decoded/received data.

0=No symbology identifier is

sent.

1=The Code ID is sent.
2=The AIM ID is sent.
3=The SymModifier is sent.

SoundConnect

Enables and disables
• The sound that ScanWedge makes

when starting up, shutting down, or
restarting.

• The audio notification when an IrDA

session is established and closed
and the serial port is opened and
closed.

0=Disabled
1=Enabled

Note: Audio notifications for

errors can’t be disabled.

MessageConnect

This key applies only
to the IrDA and serial
ports.

Enable and disables a notification
message when an IrDA session is
established and closed and the serial
port is opened and closed.

0=Disabled
1=Enabled

Accept EZConfig

This key applies only
to the decoder.

Enables and disables ScanWedge’s
compatibility with EZConfig Client when
decoding bar codes.

0=Disabled; ScanWedge

processes EZConfig
barcodes as it would any
other barcode.

1=Enabled; ScanWedge

recognizes EZConfig
barcodes and passes them
on to the EZConfig Client for
further processing.

Settings Section

The Settings section determines how ScanWedge interprets data from the decoder, serial port, and IrDA
interface.

0 = Disable 1 = Enable

Settings Section
Key

Description

Default
Value

Available Values

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands