Honeywell Dolphin 9900 Page 167 User Manual Download

Page: 167 / 170

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

13 - 1

Customer Support

Technical Assistance

If you need assistance installing or troubleshooting your device, please call your distributor or the nearest
technical support office:

North America/Canada

Telephone:

(800) 782-4263
(8 a.m. to 6 p.m. EST)

Fax number:

(315) 554-6705

E-mail:

[email protected]

Latin America

Telephone: (803)

835-8000

Telephone:

(800) 782-4263

E-mail:

[email protected]

Brazil

Telephone:

+55 (21) 3535-9100

Fax:

+55 (21) 3535-9105

E-mail:

[email protected]

Mexico

Telephone: (803)

835-8000

E-mail:

[email protected]

Europe, Middle East, and Africa

Telephone:

+31 (0) 40 7999 393

Fax:

+31 (0) 40 2425 672

E-mail:

[email protected]

Asia Pacific

Telephone - Hong Kong:

+852-3188-3485 or 2511-3050

Telephone - China:

+86 21 6361 3818

E-mail:

[email protected]

Japan

Telephone:

+813 5770-6312

E-mail:

[email protected]

Malaysia

Telephone: +603-6201-7020
E-mail:

[email protected]

Online Technical Assistance

You can also access technical assistance online at

www.honeywell.com/aidc

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands