Honeywell Dolphin 9900 User Manual Download Page 124

Page: 124 / 170

6 - 20

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

RAM INFO

Sample Data

This entry specifies the …

Total Installed RAM

128 MB

Actual size of installed RAM chip.

Total User RAM

128 MB

Total RAM available for file system and program
memory after kernel overhead.

Min File System Size

16 MB

Minimum sized allowed for the file system.

File System Size

23 MB

Current size of the file system.

Min Program Memory
Size

64 MB

Minimum size allowed for program memory.

Program Memory Size

95 MB

Current size of the program memory.

Current Split %

Percentage of the Total User RAM allocated to the file
system.

Valid Split % Range

12% - 50%

Valid % range that can be used when setting file
system size. If set out of range value will be set to
closest min or max.

IMAGER INFO

Sample Data

This entry specifies the …

PSOC Version

2.3

Current PSOC revision.

AimerXoffset

448

Imager’s AimerXoffset parameter.

AimerYoffset

239

Imager’s AimerYoffset parameter.

BitsPerPixel

Imager’s BitsPerPixel parameter.

EngineID

Imager’s EngineID parameter.

ImagerCols

752

Imager’s ImagerCols parameter.

ImagerRows

480

Imager’s ImagerRows parameter.

Rotation

Imager’s Rotation parameter.

YDepth

Imager’s YDepth parameter.

Sample SysInfo File

Field

Sample Data

This entry specifies the …

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Honeywell Dolphin 9900, User Manual, Page: 124 / 170

Search results

Summary of Contents for Dolphin 9900

Reviews: