Honeywell Dolphin 9900 Page 73 User Manual Download

Page: 73 / 170

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

4 - 5

RFON

The RF radio is Enabled.

Radio

GSMON

The GSM radio is enabled.

BTON

The Bluetooth radio is enabled.

RFGSMBTOFF

The RF, GSM, & Bluetooth radios are disabled.

29KEY

The terminal has a 29-key keyboard.

Keyboard

35KEY

The terminal has a 35-key keyboard.

38KEY

The terminal has a 38-key keyboard.

43KEY

The terminal has a 43-key keyboard.

56KEY

The terminal has a 56-key keyboard.

NO_KEY

The terminal has a 56-key keyboard.

Start Options

Start Options define the required system parameters for a software application to launch. The following
values can be entered for the StartOption key, wherever it appears:

Option Name

The program launches if …

Category

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands