Honeywell Dolphin 9900 Page 90 User Manual Download

Page: 90 / 170

5 - 12

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

Formatting Section

ScanWedge supports data formatting.

The Formatting section contains subsections and each subsection supports one data format.

Formatting Subsections

Subsection
Key

Description

Default
Value

Available Values

Format

Specifies data formatting parameters

Empty

See

Available Data Formatting

Commands on page 5-13.

CodeID

Identifies the Code ID that the bar code's
symbology must have for the format to be
applied. The Code ID is a single character that
is case-sensitive; e.g., set CodeID=j to apply
the format to Code 128 only.

Empty

Empty=No Code ID
X=See

Code ID on page 5-14.

Length

Determines the length the bar code data must
have for the format to be applied.

Empty

Empty=Format applies to any

length

0=Format applies to any length
X=The length

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands