Honeywell Dolphin 9900 Page 11 User Manual Download

Page: 11 / 170

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

1 - 5

Upgrading Power Tools

Dolphin Power Tools come loaded in every Dolphin terminal and are included in system upgrades.

Acquiring Upgrades

Upgrades are available from

Customer Support

(see page 13-1) or

www.honeywell.com/aidc

Installing an Upgrade to the Workstation

Power Tools upgrades come in the form of an upgrade executable that installs upgrade files to the
workstation. Transfer the appropriate upgrade files to the Dolphin terminal.

Requirements: An active Microsoft

ActiveSync connection between a host workstation and the Dolphin terminal.

Download the new Honeywell Power Tools and Demos for WM 6.0 Setup.exe to the Program
Files folder on the workstation.

Click the Honeywell Power Tools and Demos for WM 6.0 Setup.exe to install.

Click Next. If you accept the terms of the license agreement, select I accept the terms…

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands