Honeywell Dolphin 9900 Page 88 User Manual Download

Page: 88 / 170

5 - 10

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

GoodScanFreq

Sound frequency used for play a
custom good scan beep.

Note: The Window's "Good Decode"

sound (if defined in the control
panel) takes precedence over
this option.

2749

Variable

Use the up and down arrows to

change the number

Type in the code for the sound
you want.

GoodScanLen

Number of milliseconds to play the
sound as specified in GoodScanFreq
key.

BadScanFreq

Sound frequency used for play a
custom bad scan beep.

Note: The Window's "Bad Decode"

sound (if defined in the control
panel) takes precedence over
this option.

523

BadScanLen

Number of milliseconds to play the
sound as specified in BadScanFreq
key.

Decode Section

The Decode section specifies decoder settings when using the decoder with ScanWedge.

ScanWedge Entry

Description

Default
Value

Available Values

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands