Honeywell Dolphin 9900 Page 139 User Manual Download

Page: 139 / 170

Dolphin® Power Tools User’s Guide

Rev A

8/6/08

9 - 1

Network Utilities

Accessing Network Utilities

Tap Start > Power Tools > Network Utilities

. The Network Utilities window opens.

Standard Network Utilities

There are three Network Utilities that mirror DOS-prompt functions of your workstation:

•

IP Config

(see page 9-2)

•

Ping

(see page 9-4)

•

Route

(see page 9-6)

WiFi Status

WiFi Status helps you monitor the on-board 802.11b radio:

•

WiFi Status

(see page 9-10)

Radio Settings

There are two Power Tools on the Network Utilities window that enable you to backup and restore radio
settings in the registry.

•

Backup Radio Settings

(page 9-12)

•

Restore Radio Settings

(page 9-12)

Note: WiFi Status and the Radio Settings Power Tools appear on this window only if an RF radio is installed in the

terminal.

Summary of Contents for Dolphin 9900











































































































































































Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands

Honeywell Dolphin 9900, User Manual

Search results

Summary of Contents for Dolphin 9900

Reviews:

Related manuals for Dolphin 9900

Brands by name

Popular brands