Honeywell Dolphin 9900 Page 156 User Manual Download | Manualshive

Page: 156 / 170

background image

10 - 6

Rev A

8/6/08

Dolphin® Power Tools User’s Guide

Start Options

Start Options define the required system parameters for a software application to launch. The following
values can be entered for the StartOption key, wherever it appears:

Option Name

The program launches if …

Category

DISABLED

Never, regardless of other startup options specified.

None

COLDBOOT

The terminal has performed a cold boot.

Boot type

WARMBOOT

The terminal has performed a warm boot.

TOUCH

The terminal has a touch screen display installed.

Touch Screen

NONTOUCH

The terminal doesn’t have a touch screen display installed.

BATCH

The terminal is a batch unit (no RF or internal modem cards installed).

Mobility

RF

The terminal has an RF card installed (e.g., Cisco 802.11b).

GSM

The terminal has a GSM radio.

BT

The terminal has a Bluetooth radio.

MODEM

The terminal has an internal modem card installed.

IMAGER

The terminal has an imager installed.

Scanner

LASER

The terminal has a laser scanner installed.

BLIND

The terminal has no laser or imager installed.

ANYSCAN

The terminal has either an imager or a laser scanner installed.

RFON

The RF radio is Enabled.

Radio

GSMON

The GSM radio is enabled.

BTON

The Bluetooth radio is enabled.

RFGSMBTOFF

The RF, GSM, & Bluetooth radios are disabled.

«
...
154
155
156
157
158
...
»

Summary of Contents for Dolphin 9900











































































































































































Reviews:

No comments

Related manuals for Dolphin 9900

Brand: Easee Pages: 12

Brand: Hama Pages: 4

24V/200Ah Series

Brand: Mec Pages: 4

Brand: FeinTech Pages: 5

Brand: Naztech Pages: 18

OE Elsafe ARC-H

Brand: OE electrics Pages: 2

Brand: Hyperion Pages: 6

Brand: EnerSys Pages: 6

Brand: AVer Pages: 17

Brand: Metabo Pages: 16

Brand: Stanley Pages: 156

Brand: Vantage Hearth Pages: 6

IMPRES PMPN4527

Brand: Motorola solutions Pages: 17

Brand: WARRIOR Pages: 15

Brand: ArSilicii Pages: 12

Brand: hager Pages: 4

Brand: BTI Pages: 48

APW-CCT300 Series

Brand: AlzaPower Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands