Heat & Glo PRIMO48 Installation Manual Download

Page: 76 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

Appliance Setup

A. Remove the Shipping Materials

Remove shipping materials from inside or underneath

the

rebox. Verify all components are with the

replace.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated
inside the

rebox or underneath in the control cavity.

F. Barrier Glass

Barrier Glass Weights

PRIMO48 PRIMO60

PRIMO72

12 lbs

14 lbs

18 lbs

Figure 11.1. Barrier Glass - Clean Face Finish

TILT OUT

WARNING! Risk of Injury!

Glass is heavy. Use suction

cups to handle glass.

Remove Barrier Glass - Clean Face Finish

1. Press glass suction cups

rmly against glass to create

a solid hold.

2. Slide glass straight up behind

nishing material. See

Figure 11.1.

3. Tilt bottom out as shown in Figure 11.1. Slide glass

down to remove it from the appliance.

4. Set glass on prepared work surface.

WARNING! Risk of Injury!

Handle barrier glass with

care. Inspect the glass for cracks, chips or scratches.

•

DO NOT

strike, slam or scratch glass.

•

DO NOT

operate

replace with glass removed, cracked,

broken or scratched.

•

Replace as a complete assembly.

CAUTION! Risk of Injury!

Glass installation and removal

must be performed by a quali

ed service technician. See

chart below for barrier glass weights.

• PRIMO60 AND PRIMO72 MODELS: It is recom-

mended that glass installation and removal be per-
formed by two quali

ed service technicians.

Replacing Barrier Glass - Clean Face Finish

1. Press glass suction cups

rmly against glass to create

a solid hold.

2. Tilt glass and slide glass between

nishing material

and barrier glass tabs. See Figure 11.2.

3. Center the barrier glass left to right.
4. Tilt bottom in toward appliance. Set glass down into

position on rubber bumpers.

NOTE:

When barrier glass is installed, a vertical gap of

approximately 3/8 inch is formed between the bottom of
the glass and the transition media tray. This gap allows
adequate air

ow through the appliance.

CAUTION! Risk of Cuts or Abrasions.

Wear protective

gloves and safety glasses during installation. Sheet metal
edges are sharp.

CAUTION! Risk of Overheating!

Vertical gap 3/8 inch

required for proper air

ow.

THIS SIDE OUT

E. Install Media

A media kit is available for use with the PRIMO models.

Install rock media according to instructions included with
media kit.

D. Install Modern Log Set

An optional log set is available for use with the PRIMO

models. Install the log set per instructions included with
kit.

C. Install Burner Glass

Install the burner glass according to the instructions in

Section 6.E.

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands

Heat & Glo PRIMO48, Installation Manual

Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands