Heat & Glo PRIMO48 Installation Manual Download

Page: 62 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

7. Set transition media tray into position as shown in Figure

10.16. The return bends are at the bottom of the tray.
The rear return bend should be positioned in between
the glass frame and the glass frame bracket. Ensure
tray is positioned

ush with appliance opening.

Figure 10.15 Install Transition Glass Panel Bracket

EXISTING HOLES

8. Install glass transition panel bracket on left and right

sides of appliance opening using two self-tapping
screws. See Figures 10.14, 10.15 and 10.16 for details.

9. Install transition glass panels by securing with tabs on

left and right sides of appliance. See Figures 10.16
and 10.17.

Figure 10.14 Form Transition Glass Panel Bracket

SELF-TAPPING SCREWS GO

SELF-TAPPING SCREWS GO
THROUGH EXISTING HOLES

THROUGH EXISTING HOLES

FORM

FORM
HAND BEND

HAND BEND

INSIDE VIEW OF OUTER WRAP

TRANSITION GLASS PANEL BRACKET

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands

Heat & Glo PRIMO48, Installation Manual

Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands