Heat & Glo PRIMO48 Installation Manual Download Page 22

Page: 22 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

PVI-SLP Baf

e Adjustment

Figure 4.6 PVI-SLP Baf

e Indicator

The PVI-SLP has a baf

e adjustment which must remain

set in the closed position. This baf

e adjustment is

located alongside the motor. The baf

e adjustment is

measured using the holes on the indicator bar of the
PVI-SLP baf

e. This bar raises as the baf

e is opened

and lowers as the baf

e is closed. When only one hole is

showing, the baf

e is closed. The PRIMO requires that

the baf

e MUST remain set in the CLOSED position as

indicated in Figure 4.6.
For more information regarding installation of the PVI-

SLP, refer to the instruction included with that accessory.

CAUTION! Risk of Overheating!

Set and secure baf

indicator as instructed. Overheating could occur causing
appliance to shut down.

PVLP-SLP Baf

e Adjustment

DO NOT REMOVE THIS SCREW

CAUTION! Risk of Overheating!

DO NOT remove the

locking screw on the baf

e. Appliance could overheat.

Figure 4.7 PVLP-SLP Baf

e Locking Screw

The PVLP-SLP baf

e is closed when the locking screw

remains installed. The PRIMO requires that the baf

MUST remain in the CLOSED position as indicated in

Figure 4.7.
For more information regarding installation of the PVLP-

SLP, refer to the instruction included with that accessory.

INDICATOR BAR

PRIMO48/PRIMO48ST (NG) Only:

Baf

e Setting Exception: Due to the tendency of air to

move more quickly through the power vent in a smaller
size appliance, the PRIMO48/PRIMO48ST may require
a “two-hole” setting instead of being closed. If the pilot is
unstable, adjust the baf

e. See the PVI-SLP installation

instructions for baf

e adjustment information.

PRIMO48/PRIMO48ST (NG) Only:

Baf

e Setting Exception: Due to the tendency of air to

move more quickly through the power vent in a smaller
size appliance, the PVLP-SLP baf

e may need to be

opened up no more than 1/2 inch on the PRIMO48 and
PRIMO48ST. If the pilot is unstable, adjust the baf

See the PVI-SLP installation instructions for baf

e adjust-

ment information.

G. Power Vent Baf

e Adjustment

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Heat & Glo PRIMO48, Installation Manual, Page: 22 / 88

Search results

Summary of Contents for PRIMO48

Reviews: