manualshive.com logo in svg

Heat & Glo PRIMO48, Installation Manual, Page: 21 / 88

Share
Download
Heat & Glo PRIMO48 Installation Manual Download Page 21

21

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16 

MAXIMUM 

VERTICAL

DROP

FROM 

APPLIANCE

FROM 

APPLIANCE

FROM 

APPLIANCE

VERTICAL TERMINATION
PVI-SLP ONLY

HORIZONTAL TERMINATION
PVI-SLP  OR PVLP-SLP

NOTE

:  Maximum total vent run= Total vertical vent run + Total horizontal vent run

**= Horizontal termination allowed with both PVI-SLP and PVLP-SLP

PRIMO72/PRIMO72ST

 = Each 1 ft. of 

vertical drop decreases total allowable length 
by 3 ft.

PRIMO48/PRIMO48ST & PRIMO60/
PRIMO60ST

 =

 

Each 1 ft. of vertical drop  

decreases total allowable length by 2 ft.

*

NOTE:

NOTE: The PVI-SLP and the PRIMO 
appliance must be separated by a 
minimum of 3 ft. of pipe.  Refer to the 
PVI-SLP instructions included with the 
PVI-SLP kit.

Figure 4.5

Fire Risk.   Explosion Risk.
Do NOT pack insulation or other combustibles between ceiling 

fi

 restops.

•  ALWAYS maintain speci

fi

 ed clearances around venting and 

fi

 restop systems.

•  Install wall shield and ceiling 

fi

 restops as speci

fi

 ed.

Failure to keep insulation or other material away from vent pipe could cause 

fi

 re.

WARNING

WARNING! Risk of Fire!  

Vertical termination is 

NOT

 allowed with PVLP-SLP. Fire could occur.

APPROVED VENT SYSTEMS

HORIZONTAL 

TERMINATION

VERTICAL

TERMINATION

DVP VENT

COMPONENTS

SLP VENT

COMPONENTS

PVI-SLP

ALLOWED

ALLOWED

ALLOWED

ALLOWED

PVLP-SLP

ALLOWED

NOT ALLOWED

ALLOWED

ALLOWED

NOTICE:  

If a pipe con

fi

 guration includes a 

vertical component that goes downward, a 
vertical component going back upward is not 
allowed. Condensation will occur.

ADAPTER KITS

PART NUMBER

PART DESCRIPTION

DVP-2SL

(Included with 

PRIMO)

Adapts from 8 in. DVP-se-
ries starting collars to 6-5/8 
in. SLP series vent pipe.

DVP-SLP24

Adapts from 8 in. DVP-se-
ries starting collars to 6-5/8 
in. SLP series vent pipe.

APPROVED VENT MAXIMUMS

MODEL

VENT 

SYSTEM

MAX. TOTAL 

VENT RUN (FT.)**

MAX. 90° 

ELBOWS

MAX. VERT. 

DROP (FT.)

PRIMO48
PRIMO48ST

PVI-SLP

60

6

12*

PVLP-SLP

60

6

12*

PRIMO60
PRIMO60ST

PVI-SLP

50

5

9*

PVLP-SLP

50

5

9*

PRIMO72
PRIMO72ST

PVI-SLP

40

4

9*

PVLP-SLP

40

4

9*

Summary of Contents for PRIMO48

























































































Reviews:

No comments