manualshive.com logo in svg

Heat & Glo PRIMO48, Installation Manual, Page: 83 / 88

Share
Download
Heat & Glo PRIMO48 Installation Manual Download Page 83

83

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16 

Optional Wire Harness

DESCRIPTION

PART NUMBER

10 ft. PV Wire Harness

PVI-WH10

20 ft. PV Wire Harness

PVI-WH20

40 ft. PV Wire Harness

PVI-WH40

60 ft. PV Wire Harness

PVI-WH60

80 ft. PV Wire Harness

PVI-WH80

100 ft. PV Wire Harness

PVI-WH100

PVI-SLP

Power Vent Inline

Note:  

Wire harnesses required to power the PVI-SLP 

connect to the appliance and are ordered separately from 
PVI-SLP. Contact your dealer to order.

12-1/2 IN.
318 mm

20-3/4 IN.
527 mm

13-5/8 IN.
346 mm

EFFECTIVE LENGTH
32 IN. (813 mm) MIN.
35 IN. (889 mm) MAX.

Note:  

Termination caps listed in Section 12.A are 

approved for use with the PVI-SLP.

Figure 12.5  Vent Components

16 IN.

406 mm

15 IN.

(381 mm)

16-11/16 IN.

(424 mm)

9-3/16 IN.
(233 mm)

4-1/2 IN.

114 mm

16-11/16 IN.

424 mm

13-5/8 IN.
(346 mm)

12-1/2 IN.
(318 mm)

SLP-LPC

SLP Low Pro

fi

 le Cap

SL-2DVP
Adapter

3-15/16 in.

(101 mm)

6-11/16 in.

(169 mm)

8 in.

(203 mm)

3-15/16 in.

(101 mm)

3-13/16 in.

(97 mm)

5-1/16 in.

(128 mm)

6-3/8 in.
163 mm

4-3/16 in.

106 mm

4-5/8 in.
117 mm

5-1/16 in.

128 mm

8-1/8 in.
206 mm

DVP-2SL
Adapter

4 in.

102 mm

Summary of Contents for PRIMO48

























































































Reviews:

No comments