Heat & Glo PRIMO48 Installation Manual Download

Page: 36 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

Figure 6.17. HEAT-ZONE-PRIMO and HEAT-OUT-PRIMO Features

HEAT-ZONE-PRIMO

Heat-Out-Primo

DAMPER

HEAT-ZONE-PRIMO Collar

Wall Switch

PowerFlow

Heat

Management Toggle

LED COLOR
SWITCHES

**ATTACH WITH
ZIP TIE AT
DAMPER

HEAT-ZONE-PRIMO

HEAT-OUT-PRIMO

COLLAR

*The HEAT-OUT-PRIMO may be installed in either position shown above.

** Use included zip ties to attach the flex ducting to the damper.

*Note: Remove only one of the two middle seal plates if installing
the HEAT-OUT-PRIMO. The other plate must remain installed.

HEAT-ZONE-PRIMO Collar

HEAT-OUT-PRIMO Incorporated with HEAT-ZONE-PRIMO

WARNING! Risk of Fire!

Verify damper is opera-

tional. Overheating will occur if damper does not
open and close.

WARNING! Risk of Overheating!

Damper MUST

be installed with crimped side up. Damper will not
function properly.

* = Optional HEAT-OUT-PRIMO location

For wiring information, see Figure 8.8:
HEAT-ZONE-PRIMO incorporated with
HEAT-OUT-PRIMO.

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands

Heat & Glo PRIMO48, Installation Manual

Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands