Heat & Glo PRIMO48 Installation Manual Download

Page: 66 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

C. Black Granite Surround Finish (Black

Granite Interior)

NOTE: USE 1/2 INCH SHEETROCK

Wall Preparation

Figure 10.19 shows the PRIMO installed in a sheetrocked
wall.

1. Install 1/2 inch sheetrock up to appliance top, bottom

and sides of the appliance opening as shown in Figure
10.19 and 10.20.

2. Do not install the sheetrock trim strips which are

included with the appliance. The strips would keep the
granite from being installed level. They are required
for the Clean Face

nishing method only.

3. A flat sheetrock surface will allow for the granite

surround to sit

at. Sheetrock seams will lead to granite

not being level. See Figure 10.19.

Figure 10.20. Do Not Install Sheetrock Trim Strips

PRIMO48-GR PRIMO48ST-GR
PRIMO60-GR PRIMO60ST-GR
PRIMO72-GR PRIMO72ST-GR

NOTICE:

DO NOT install sheetrock trim strips. Granite

pieces will not be level.

The wall and granite pieces must be clean, free from
dust and construction debris, and dry before beginning
installation. Dust or moisture may prohibit the adhesive
from performing effectively.
For the adhesive, choose a 100% silicone or strong

construction adhesive with an aggressive tack intended
to hold heavy material and that also is approved for high
temperatures (250°F minimum).

DO NOT INSTALL SHEETROCK TRIM STRIPS WITH

GRANITE SURROUND

DO NOT INSTALL

SHEETROCK
SEAM LOCATIONS-NOT
DESIREABLE

SHEETROCK
SEAM LOCATIONS-IDEAL

Figure 10.19. Sheetrock Seams - Prior to Granite installation

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands

Heat & Glo PRIMO48, Installation Manual

Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands