Heat & Glo PRIMO48 Installation Manual Download Page 30

Page: 30 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

• Install the HEAT-ZONE-PRIMO collars on the left and

right sides of the appliance with screws. See Figure
6.7.

• Attach included air duct to the HEAT-ZONE-PRIMO

collars with gear clamps. See Figure 6.8.

• Attach both mounting brackets to the fan housing.

See Figure 6.8.

• Mount fan housing in desired location. See Figures

6.5, 6.10 and 6.11.

• Attach round to oval adapter to fan housing with two

screws. See Figure 6.8.

• Attach

included

exible ducts to round to oval adapter

with gear clamps.

Note:

6 Inch metal duct can be used in place of the in-

cluded

exible ducts.

Figure 6.7 HEAT-ZONE-PRIMO

DO NOT
REMOVE
KNOCKOUTS

HEAT ZONE

COLLAR LOCATION

LEFT AND RIGHT SIDES

SQUARE
VENT
PIPE GASKET

HEAT-OUT-PRIMO
SEAL PLATES

Figure 6.9

18 in.

6-3/4 in.

MINIMUM SPACE

REQUIRED FOR

90 DEGREE BEND

Fan Housing

Round to Oval Adapter

6 in. Round Air Duct

Gear Clamp

Screws

Gear Clamp

Mounting Bracket
(Both Sides)

Figure 6.8

WARNING! Risk of Fire!

HEAT-OUT-PRIMO seal plates

MUST remain installed. Appliance could overheat.

WARNING! Risk of Fire! DO NOT

fold/kink/pinch/ob-

struct 6 inch

exible ducts. Appliance could overheat.

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Heat & Glo PRIMO48, Installation Manual, Page: 30 / 88

Search results

Summary of Contents for PRIMO48

Reviews: