manualshive.com logo in svg

Heat & Glo PRIMO48, Installation Manual, Page: 35 / 88

Share
Download
Heat & Glo PRIMO48 Installation Manual Download Page 35

35

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16 

HEAT-OUT-PRIMO

DAMPER***

HEAT-OUT-PRIMO 
Collar

**ATTACH WITH 
   ZIP TIE AT 
   DAMPER

*The HEAT-OUT-PRIMO may be installed in either position shown above.

**  Use included zip ties to attach the flex duction to the damper. 
*** Verify damper is operational and no obstructions, such as screws,  are present.
  

 

*Note:   Remove only one of the two middle seal plates if installing 
the HEAT-OUT-PRIMO.  The other plate must remain installed.

*

 
PowerFlow

TM

 Heat 

Management Toggle

LED COLOR 
SWITCH

DO NOT install wall switch plate and toggle 
switch if only HEAT-OUT-PRIMO is installed. 

Install wall switch plate and toggle switch 
only when both HEAT-OUT-PRIMO and 
HEAT-ZONE-PRIMO are installed

LED COLOR 
SWITCH

INSTALL

Figure 6.16. HEAT-OUT-PRIMO

*

HEAT-OUT-PRIMO Feature - Configuration

WARNING! Risk of Overheating! 

Damper MUST 

be installed with crimped side up. Damper will not 
function properly.

WARNING! Risk of Fire! 

Verify damper is opera-

tional.  Overheating will occur if damper does not 
open and close.

* = Optional HEAT-OUT-PRIMO location

Summary of Contents for PRIMO48

























































































Reviews:

No comments