Heat & Glo PRIMO48 Installation Manual Download Page 49

Page: 49 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

Figure 8.7 PRIMO Wiring Diagram

• Wire the appliance junction box to 110-120 VAC for

proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT

wire

IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.

• Refer to Figure 8.7, IPI Wiring Diagram.
• This appliance is equipped with an IntelliFire™

Plus

control valve which operates on a 6 volt/1.5 AMP system.

• Plug the 6 volt transformer plug into the appliance junction

box to supply power to the appliance.

IntelliFire

Plus Ignition System Wiring

B. Wiring Requirements

RC300 4.5V DC
(AAA X 3)

2273-308

2310-211

6V TRANSFORMER

BLK

2206-299 LOCK OUT
RESET SWITCH

2196-150
PVI MODULE

2196-200 PVI-WIRE HARNESS

HEAT-ZONE-PRIMO

LED’S
2310-062

2155-204

LED SWITCH

2155-752

JUNCTION BOX

2310-211

2166-335 AUX

2155-755

(PRIMO72ST ONLY)

107-558A MALE/FEMALE
WIRE HARNESS

PVI-SLP

2155-033
JUMPER
WIRE

PVLP-SLP

2005-021
WIRE PLUG
ASSEMBLY

2310-202
THERMODISC

HEAT-OUT-PRIMO

2310-204
THERMODISC

PVI-SLP OR PVLP-SLP REQUIRED

2300-753
JUMPER WIRE

PVI-WHXX

Thick line denotes wiring
supplied by electrician.

RED

BROWN

2179-300

2159-310

2273-308

SEE THROUGH ONLY

2310-200

(TO VALVE)

ORG

GRN

GROUND

BLK



Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Heat & Glo PRIMO48, Installation Manual, Page: 49 / 88

Search results

Summary of Contents for PRIMO48

Reviews: