Heat & Glo PRIMO48 Installation Manual Download

Page: 77 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

Figure 11.2. Replace Barrier Glass - Clean Face Finish

BARRIER GLASS TABS

THIS SIDE OUT

NOTE: INSTALL BARRIER
GLASS PRINTED SIDE
OUT.“THIS SIDE OUT”
MUST BE LEGIBLE ON
BARRIER GLASS.

3/8 IN. VERTICAL

GAP

REQUIRED

Removing Barrier Glass - Black Granite Finish

1. Slide side granite pieces inward toward center of

re-

place to disengage from the key slots. See section 10.C.
2. Remove (unscrew) D-shaped retaining tabs.
3. The glass rests against the barrier glass support

bracket. See Figure 11.4.

4. Use suction cups to remove barrier glass.
5. Rotate/tilt the bottom of the glass outward to remove.

See Figure 11.4.

6. Set the glass on a prepared work surface.

Figure 11.4 Barrier Glass - Black Granite Finish

BARRIER GLASS

GLASS SUPPORT
BRACKET

D-SHAPED RETAINING TAB

THIS SIDE OUT

NOTE: INSTALL BARRIER
GLASS PRINTED SIDE
OUT.“THIS SIDE OUT” MUST
BE LEGIBLE ON BARRIER
GLASS.

GLASS GASKET BULB

LOCATED BEHIND GRANITE

Replacing Barrier Glass - Black Granite Finish

1. Use suction cups to pick up barrier glass.
2. Place the top edge of the barrier glass behind the top

granite trim.

Note: Ensure the glass gasket is installed.

The glass

gasket bulb should be positioned on the outside sur-
face of the barrier glass surround as shown in Figure
11.4. It is labeled “THIS SIDE OUT.”

CAUTION! Risk of Injury!

Glass gasket shall be in-

stalled on barrier glass! Hot glass will cause burns.

3. The glass rests against the barrier glass support

bracket as shown in Figure 11.4.

Figure 11.3 Glass Gasket Detail - Black Granite Finish

GLASS GASKET BULB

TOP

BOTTOM

4. Attach and tighten the D-

shaped retaining tab. See

Figure 11.4.

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands

Heat & Glo PRIMO48, Installation Manual

Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands