Heat & Glo PRIMO48 Installation Manual Download | Manualshive

Page: 54 / 88

background image

54

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

Figure 9.7 Gas Access Location - Left Side

D. Gas Connection

• Refer to Figure 9.7 for location of gas line access in

appliance.

• Gas line must be run through the left side of appliance.
• The gap between supply piping and gas access hole

may be caulked with caulk with a minimum of 300ºF
continuous exposure rating or stuffed with non-
combustible, unfaced insulation to prevent cold air
in

fi

ltration.

• Gas access plate must remain installed or barrier glass

will become hot.

• Ensure that gas line does not come in contact with outer

wrap of the appliance. Follow local codes.

• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)

connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion!

Support control

when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion!

Gas build-up dur-

ing line purge could ignite.

• Purge should be performed by

qualified service

technician

.

• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks

or open

fl

ames.

Turn the appliance on. The appliance is equipped with a
pre-purge safety feature. After the pre-purge, the appli-
ance will take approximately 2 to 3 minutes to light. It will
take a short time for air to purge from lines. When purging
is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all

fi

ttings and connections with a non-corrosive

commercially available leak-check solution.

DO NOT

use

open

fl

ame. Fittings and connections could have loos-

ened during shipping and handling.

WARNING! Risk of Fire! DO NOT

change valve settings.

This valve has been preset at the factory.

GAS ACCESS PLATE

NOTE: GAS ACCESS PLATE MUST
REMAIN INSTALLED

LOWER ACCESS COVER PANEL

ELECTRICAL ACCESS PLATE

NOTE: ELECTRICAL ACCESS PLATE
MUST REMAIN INSTALLED

Figure 9.8 Electrical Access Location - Right Side

Figure 9.6 Gas Fitting Access- Lower Left Side

GAS VALVE

GAS CONNECTION

CAUTION! Risk of Burns!

Do NOT remove gas access

plate.
• Hot barrier glass could cause burns.
• Appliance will overheat.

«
...
52
53
54
55
56
...
»

Summary of Contents for PRIMO48

























































































Reviews:

No comments

Related manuals for PRIMO48

Brand: Harrie Leenders Pages: 26

MENTOR hydro Series

Brand: ARTE Pages: 42

Brand: Superior Pages: 12

Brand: Napoleon Pages: 68

MANDALAY Series

Brand: Warnock Hersey Pages: 38

Freedom Bay Fireplace Insert

Brand: Lopi Pages: 34

Brand: Valor Pages: 12

Brand: Escea Pages: 2

Brand: Napoleon Pages: 4

Brand: MHG Heating Pages: 28

CC-RON00-1X0 Ronda 160

Brand: Nordpeis Pages: 36

Brand: Oblica Pages: 10

Brand: tropitone Pages: 4

Brand: JAYLINE Pages: 11

Brand: Dimplex Pages: 16

Brand: Charlton & Jenrick Pages: 28

Brand: Coleman Pages: 2

MERCURY MERC32IL

Brand: Majestic Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands