Heat & Glo PRIMO48 Installation Manual Download

Page: 45 / 88

Heat & Glo • PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual • 2310-970 Rev. L • 2/16

Note:

When using termination caps with factory-supplied

heat shield attached, no additional wall shield

restop is

required on the exterior side of a combustible wall.

Install Horizontal Termination Cap (PVI-SLP)

WARNING! Risk of Fire!

The telescoping

ue section of

the termination cap MUST be used when connecting vent.

• 1-1/2 (38 mm) minimum overlap of

ue telescoping

section is required.

Failure to maintain overlap could cause overheating
and

re.

• Vent termination must not be recessed in the wall. Siding

may be brought to the edge of the cap base.

• Flash and seal as appropriate for siding material at

outside edges of cap.

• When installing a horizontal termination cap, follow

the cap location guidelines as prescribed by current

ANSI Z223.1

and

CAN/CGA-B149

installation codes

and refer to Section 6 of this manual.

CAUTION! Risk of Burns!

Local codes may require in-

stallation of a cap shield to prevent anything or anyone
from touching the hot cap.

NOTICE:

For certain exposures which require superior

resistance to wind-driven rain penetration, a

ashing kit

and HRC caps are available. When penetrating a brick
wall, a brick extension kit is available for framing the brick.

Figure 7.16 Venting Through the Wall - PVI-SLP

INTERIOR

HEAT SHIELD OR

EXTENDED

HEAT SHIELD

WALL SHIELD

FIRESTOP

HEAT SHIELD

1-1/2 IN. (38 MM) MIN.

OVERLAP

SHEATHING

SLIP SECTION

CAN BE EXTENDED

INNER VENT

OUTER VENT

EXTERIOR

Figure 7.17 Venting Through the Wall - PVLP-SLP

INTERIOR

SHEATHING

EXTERIOR

INNER VENT

OUTER VENT

10 IN.

13 IN.

ZERO CLEARANCE

(SIDES AND BOTTOM)

ZERO CLEARANCE

(TOP)

1-1/2 IN. CLEARANCE

(BACK)

Install PVLP-SLP Horizontal Termination
Cap

WARNING! Risk of Fire!

The telescoping

ue section of

the termination cap MUST be used when connecting vent.

• 1-1/2 (38 mm) minimum overlap of

ue telescoping

section is required.

Failure to maintain overlap could cause overheating
and

re.

• Vent termination must not be recessed in the wall. Siding

may be brought to the edge of the cap base.

• Flash and seal as appropriate for siding material at

outside edges of cap.

See PVLP-SLP installation instructions
for service access information.

Summary of Contents for PRIMO48

























































































Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands

Heat & Glo PRIMO48, Installation Manual

Search results

Summary of Contents for PRIMO48

Reviews:

Related manuals for PRIMO48

Brands by name

Popular brands