manualshive.com logo in svg

Heat & Glo PRIMO48, Installation Manual, Page: 46 / 88

Share
Download
Heat & Glo PRIMO48 Installation Manual Download Page 46

46

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16  

A

GAS

B

POWER VENT

C

LOW VOLTAGE

D

120V to JUNCTION BOX

D

HEAT-ZONE-PRIMO/HEAT-OUT-PRIMO

A. General Information

WARNING! Risk of Shock or Explosion! DO NOT

 wire 

110-120 VAC to the valve or to the appliance wall switch. 
Incorrect wiring will damage controls.

NOTICE: 

This appliance must be electrically wired 

and grounded in accordance with local codes or, in the 
absence of local codes, with 

National Electric Code 

ANSI/NFPA 70-latest edition

 or the 

Canadian Electric 

Code CSA C22.1.

•  Wire the appliance junction box to unswitched 110-

120 VAC. This is required for proper operation of the 
appliance.

•  A 110-120 VAC circuit for this product must be protected 

with ground-fault circuit-interrupter protection, in 
compliance with the applicable electrical codes, when 
it is installed in locations such as in bathrooms or near 
sinks.

•  Low voltage and 110/120 VAC voltage cannot be shared 

within the same wall box.

•  See Figures 8.1, 9.7 and 9.8 for routing electrical power 

from the appliance to the power vent (PVI-SLP or PVLP-
SLP), wall switch and PowerFlow™ Heat Management 
System.

8 

8 

Electrical Information 

Electrical Service and Repair

WARNING! Risk of Shock! 

Label all wires prior to dis-

connection when servicing controls. Wiring errors can 
cause improper and dangerous operation. Verify proper 
operation after servicing.

WARNING! Risk of Shock! 

Replace damaged wire with 

type 105º C rated wire. Wire must have high temperature 
insulation.

Accessories Requirements

•  This appliance must be used with the supplied wall switch 

and remote control.

Wiring for optional Hearth & Home Technologies approved 
accessories should be done now to avoid reconstruction. 
Follow instructions that come with those accessories.

LEFT SIDE

RIGHT SIDE

GAS

ELECTRICAL

A

B

C

D

D

D

Figure 8.1 Access Plates

•  The PRIMO model requires electrical power in order to 

operate the required PowerFlow™ Heat Management 
System and power vent.  If electrical power service 
is interrupted during operation of this model, the 
appliance will not operate. 

 Battery power is not an 

option on the PRIMO.

Figure 8.2  Reset Switch Location - Bottom Left

Reset Switch

•  Press the RESET switch located on the left side of 

the transition media tray.  Use a small, 

fl

 at  object  to 

access the switch.  When the appliance has started, 

fl

 ip the reset switch back to its original position.  See 

Figure 8.2.

RESET SWITCH

Summary of Contents for PRIMO48

























































































Reviews:

No comments