background image

69

Heat & Glo  •  PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST, PRIMO72, PRIMO72ST Installation Manual  •  2310-970 Rev. L  •  2/16 

Figure 10.26.  Right Side Granite Piece Installed and Leveled

SLIDE GRANITE TO OUTSIDE 

SLIDE GRANITE TO OUTSIDE 
OF FIREPLACE

OF FIREPLACE

Figure 10.27.  Verify Side Granite Reference Dimensions

3/4 IN.

3/4 IN.

LEFT SIDE GRANITE

LEFT SIDE GRANITE

1-1/8 INCH

1-1/8 INCH

GRANITE TRANSITION BRACKET

GRANITE TRANSITION BRACKET

3.  Install right outside granite by aligning the bolts on the 

back of the granite piece with bottom hole on granite 
transition panel bracket.  Insert the bolt* in the bottom 
slot.  See Figure 10.25. Align and slide toward outside 
of appliance.  Repeat with left side granite.

 

*Bolt detail:  M6-1.00 x 25 Hex Head

Figure 10.25.  Install Side Granite Pieces

NOTICE!  

Verify the left and right side granite locations 

before installing the top and bottom granite.  See Figures 
10.25, 10.27, 10.29.

INSERT BOLT* IN BOTTOM HOLE

INSERT BOLT* IN BOTTOM HOLE

NOTE: USE 
LEVELING 
BOLTS TO 
STABILIZE 
GRANITE 
PIECES

Summary of Contents for PRIMO48

























































































Reviews: