background image

1

Majestic  •  CK36MS Contemporary Kit Instructions  •  2488-970 Rev. D  •  7/18

TOOLS 

Screw gun equipped with 1/4 in. socket or
1/4 in. wrench
3/8 in. wrench (Propane Appliances Only)
Instructions for optional glass kit, if applicable.

Leave this manual with party responsible for use 

and operation.

CK36MS

 

Models: PEARL36STIN, PEARL36PRIN

Installation Instructions

CAUTION! Do not install damaged components.

DANGER

HOT GLASS 

WILL 

CAUSE BURNS.

DO NOT TOUCH 

GLASS 

UNTIL COOLED.

NEVER 

ALLOW CHILDREN

 TO TOUCH GLASS.

A barrier designed to reduce the risk of 

burns from the hot viewing glass is provided 

with this appliance and shall be installed for 

the protection of children and other at-risk 

individuals.

Preparation

CAUTION!  Risk of Burns! 

The  fireplace  should  be 

turned off and cooled before contemporary kit is installed. 

•    Remove the CK36MS burner assembly from the base 

pan assembly by removing four screws.

•  Shut off gas supply and disconnect electrical power.
•   Remove decorative fronts, glass assemblies, lava 

rock, embers and logs, if previously installed.

CAUTION! Risk of Cuts, Abrasions or Flying Debris. 

Wear protective gloves and safety glasses during instal

-

lation. Sheet metal edges are sharp.

WARNING! Choking Hazard!  

Keep media and stones 

out of reach of children.

Note:  

If an optional LINER-36ST or LINER-36PIER kit 

will be used with the CK36MS, the LINER-36ST/LINER-

36PIER instructions will be needed during installation of 

the CK36MS kit.

Note:  

 The CK36MS is not compatible with fiber refractory.

Note: 

The control module MUST be set to 30% 

turndown when the CK36MS kit is installed.

WARNING! Risk of Injury!  

This kit must be installed by 

a qualified service technician.

Models

(U.S. or Canada)

Maximum

Input 

BTU/h

Minimum

Input BTU/h

Orifice

Size 

(DMS)

CK36MS (NG)

(0-2000 FT)

38,000 26,000

32

CK36MS (Propane)

(0-2000 FT)

29,000 19,000

52

BTU Specifications

Summary of Contents for CK36MS










Reviews: