Hach DR 6000 User Manual Download Page 47

Page: 47 / 156

Standard programs

Plug the USB storage device into the USB A interface on the
DR 6000 or connect the DR 6000 with a network drive (refer
to

section 5.2.7.4, page 39

Press

Recall Data

from the Main Menu.

Select the data category to be transferred, e.g.

Data Log

A list of the selected measurement data is displayed.

Tap on

Options

and then on the

PC & Printer

symbol.

Select the data to be sent.
The following options are available:

•

Single point

: only this selected reading will be sent

•

Filtered data

: only readings that correspond to the set

filters will be sent

•

All data

: all data in the selected data category will be

sent.

Press

to confirm.

Note: The number in parentheses is the total number of data sets
assigned to this selection.

5.3.1.4

Delete stored data from the data log

Press

Recall Data

from the Main Menu.

Press

Data Log > Options > Delete

Highlight

Single point

Filtered data

All data

and press

to confirm.

Note: The number in parentheses is the total number of data sets
assigned to this selection.

Summary of Contents for DR 6000




























































































































































Search results

Summary of Contents for DR 6000

Reviews:

Brands by name

Popular brands

Hach DR 6000, User Manual

Search results

Summary of Contents for DR 6000

Reviews:

Brands by name

Popular brands